ADC 410F Instructions d'exploitation Page 47
- Page / 79
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
6/2
Stable signal outputs when measuring tube empty 6.3
Output signals can be stabilized to values as for “zero” flow to prevent random output signals
when the measuring tube is empty or when the electrodes are not wetted in the event the
measuring tube is partially full.
- Display: 0
- Current output: 0 or 4 mA, see setting in Fct. 1.05
- Pulse output: no pulses (= 0 Hz), see setting in Fct. 1.06
Precondition:
electrical conductivity of product: ≥ 200 µS/cm,
≥ 500 µS/cm for meter sizes DN 2.5 - 15 and
1
/10”-
1
/2”
Chan
ges on amplifier PCB, see illustration in Sect. 8.9.
Switch off power source before opening the housing!
1) Unscrew cover from the terminal compartment using the special wrench. Pull off the
two plugs for supply power (3-pin) and outputs/inputs (6-pin).
2) Unscrew cover from the electronic compartment using the special wrench.
3) If provided, remove display unit. For this purpose, detach the two screws R and fold
display unit to the side, see illustration in Sect. 8.5.
4) Carefully pull off the blue 9-pin plug X1/X4 (forming the connection to the primary head).
5) Detach the 2 recessed head screws Q and carefully remove the electronic unit.
6) Join the two “semicircles” of points S1 and S3 on the amplifier board with tin solder,
see illustration in Sect. 8.9.
7) Reassemble in reverse order, points 5) - 2) above.
8) Switch on power.
9) Check setting of the low-flow cutoff SMU, Fct. 1.03, and reset if necessary:
L.F.CUTOFF switched on, range:
O
perator control:
Display Version: IFC 090 / D, see Sect. 4 and 5.3, Fct. 1.03
Basic Version: IFC 090
/ B, see Sect. 6.2.
10) After checking and/or resetting, replace the cover on the electronic compartment and
tighten using the special wrench.
NOTE: The screw thread and gasket of the housing cover should be well greased at
all times, always check for signs of damage and never allow dirt to accumulate.
Replace defective gasket immediately.
Full scale range Q
100%
Cutoff ...... values
... OFF ... ... ON ...
> 3 m/s > 10 ft/s >02 % 1 %
1 - 3 m/s 3 -10 ft/s >06 % 4 %
< 1 m/s < 03 ft/s >10 % 8 %
- Signal converters 1
- 100% 5/1 2
- Primary heads 11
- Binary outputs 12
- Current output 12
- 100% [ Hz] 13
- Part B IFC 090 20
- / D Signal converter 20
- Totalizer 21
- Overrange 21
- Flowrate 21
- Change to number setting 23
- “VALUE P” 24
- TIMECONST.: 26
- I = I only 26
- 100% (see Fct. 1.01) 35
- Dynamic response 38
- Blue 9-pin plug 60
- (connection to primary head) 60
- Order numbers 9 69
- IFC 090 electronic unit and 69
- Meter size 70
- Full-scale range 70
- Index Part E 77
- Keyword Section No. Fct. No 78
- SPECIMEN certificate 79
Produits connexes et manuels pour Mise en réseau ADC 410F
Mise en réseau ADC 410F Manuel d'utilisateur
(106 pages)
(106 pages)
Mise en réseau ADC 2 Spécifications
(34 pages)
(34 pages)
Mise en réseau ADC H2TU-C-231 Spécifications
(90 pages)
(90 pages)
Mise en réseau ADC 400F Spécifications
(26 pages)
(26 pages)
Mise en réseau ADC 2 Manuel d'utilisateur
(24 pages)
(24 pages)
Mise en réseau ADC 6 Manuel d'utilisateur
(12 pages)
(12 pages)
Mise en réseau ADC MM701G2 Manuel d'utilisateur
(134 pages)
(134 pages)
Mise en réseau ADC 320F Manuel d'utilisateur
(68 pages)
(68 pages)
Mise en réseau ADC MM701G Manuel d'utilisateur
(108 pages)
(108 pages)
Mise en réseau ADC MM701G Manuel d'utilisateur
(168 pages)
(168 pages)
Mise en réseau ADC 400F Manuel
(74 pages)
(74 pages)
Siemens Gigaset E49H manuály
Uživatelské manuály a uživatelské příručky pro Bezdrátový telefonní set Siemens Gigaset E49H.
Poskytujeme 1 manuály pdf Siemens Gigaset E49H ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Commentaires sur ces manuels