ADC MM701G Manuel d'utilisateur Page 81
- Page / 168
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Chapter 7: Implementing a Point-to-Point LAN Extension
MM701G and MM702G User Manual 73
2 Select RFC 1483 bridged from the WAN Configuration page to display the following page.
3 In the
Session Name box, assign a name to this session (it can be the same name set up for
the Remote modem).
4 In the
Virtual Path ID (VPI 0 - 4,095) box, enter the Virtual Path ID. This must match the
Virtual Path ID of the Remote modem.
5 In the
Virtual Channel ID (VCI 32 - 65,535) box, enter the Virtual Channel ID. This must match
the Virtual Channel ID of the Remote modem.
6 Click
Apply.
- User Manual 1
- Copyright 2
- Trademark Information 2
- Disclaimer of Liability 2
- ABOUT THIS USER MANUAL 3
- DOCUMENT CONVENTIONS 4
- FCC CLASS B COMPLIANCE 4
- TABLE OF CONTENTS 5
- Table of Contents 6
- Table of Contents 7
- INSTALLING THE MODEM 9
- TEP 2—DETERMINE WHAT YOU NEED 10
- STEP 4—CONNECT CABLES 11
- Wall jack with 12
- DSL service 12
- PC, hub or other 12
- LED Status Indications 13
- Connect Cables 14
- ACCESSING THE WEB INTERFACE 15
- MODEM MANAGEMENT 15
- Assign IP Addresses 16
- TCP/IP Network Configuration 16
- TEP 2—SET UP THE WEB BROWSER 17
- Set Up the Web Browser 18
- Location Bar 19
- System Status page 20
- CONFIGURING THE LAN 21
- CONFIGURE THE LAN 22
- CONFIGURE DNS RELAY MODE 24
- CONFIGURE DHCP SERVER MODE 26
- Configure: 27
- Configure DHCP Server Mode 28
- Default Lease Time 29
- Max Lease Time 29
- DHCP Default Gateway 29
- DHCP DNS Server 29
- Ethernet Mode page 31
- Half Duplex or Full Duplex 31
- CONFIGURING THE WAN 33
- CONFIGURE A NEW WAN SESSION 34
- Session Name 35
- Virtual Path ID (VPI) 35
- Virtual Channel ID (VCI) 35
- Configure a New WAN Session 36
- PPPoE routed are identical 40
- QoS Peak Cell Rate 41
- QoS Sustainable Cell Rate 41
- QoS Maximum Burst Size 41
- EDIT A WAN SESSION 44
- Edit a WAN Session 46
- CONFIGURING 47
- SYSTEM PARAMETERS 47
- ASSIGNING USER ACCESS 48
- Assigning User Access 50
- ADD A DEFAULT GATEWAY 52
- ADD STATIC ROUTE ENTRIES 53
- Destination 54
- Static Routes table 55
- ADD SNMP COMMUNITIES 56
- Add SNMP Communities 58
- CHANGE SPANNING TREE SETTING 59
- Priority 60
- Hello Time 60
- Forward Delay 60
- SAVING CHANGES 61
- Saving Changes 62
- Rebooting the Modem 64
- CONFIGURING DSL PARAMETERS 65
- Quick Configuration 66
- Advance Configuration 68
- IMPLEMENTING A POINT-TO-POINT 71
- LAN EXTENSION 71
- COMPLETE A QUICK INSTALLATION 72
- Configure the Remote Modem 74
- Configure the Remote WAN 75
- Configure the Remote LAN 77
- 2 In the 79
- 3 Click 79
- 6 Click 83
- VERIFY CONNECTIVITY 84
- CONFIGURING MODEM SECURITY 85
- CONFIGURE NAT 86
- Configure NAT 88
- MANAGING THE MODEM 89
- View Modem Status 90
- View System Log 92
- VIEW WAN STATISTICS 93
- Rx Bad Pkts 94
- Tx Bad Pkts 94
- VIEW LAN STATISTICS 95
- Rx CRC Errors 96
- Tx Collisions 96
- SmartCNCTSecurity 97
- VIEW ATM STATISTICS 98
- View G.shdsl Link Statistics 100
- View G.shdsl Error Counters 102
- Update System Software 104
- 4 Click 105
- when prompted 105
- 5 Click 105
- Factory Defaults 106
- Reset to Factory Defaults 106
- ACCESSING THE 107
- COMMAND-LINE INTERFACE 107
- CONNECT TO THE CONSOLE PORT 108
- Modem Defaults 110
- Login admin 110
- Password password 110
- SET UP THE LAN 112
- MANAGE WAN SESSIONS 114
- Add a New Session 115
- Manage WAN Sessions 116
- Permanently Save Sessions 124
- Edit an Existing Session 125
- MANAGE DSL 126
- Configure G.shdsl Parameters 127
- Manage DSL 128
- Operating Mode 129
- View G.shdsl Configuration 132
- Monitor G.shdsl Statistics 133
- CRC Error 135
- LOSW Errors 135
- Errored Seconds 135
- View ATM Counters 136
- RESTORING FACTORY DEFAULTS 138
- UPDATING SYSTEM SOFTWARE 140
- VIEWING SYSTEM INFORMATION 141
- REBOOTING THE MODEM 142
- SPECIFICATIONS 143
- OVERVIEW 144
- VLAN Support 145
- DSL Standards 145
- ATM standards 145
- Internetworking Features 145
- WAN Protocols 146
- Security 146
- Management 146
- Software Upgrade 146
- Encapsulation 147
- • Bridge MIB - 2684 148
- • MIB 1213 - MIB II 148
- Connectors 149
- LAN Interface 149
- WAN Interface 150
- Connector Pinouts 151
- DSL Port (RJ-11) 151
- 10Base-T Port (RJ-45) 152
- Console Port (RJ-45) 152
- RATE VS. REACH 153
- Rate vs. Reach 154
- CONTACTING ADC 155
- GLOSSARY 157
- Appendix D: Glossary 159
- Index 163
- ´,^s¶4_¨ 168
Produits connexes et manuels pour Mise en réseau ADC MM701G
Mise en réseau ADC 400F Manuel
(74 pages)
(74 pages)
(2 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.151 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels